Brake pedal does not return

rtessier

Bigger Hammer
Joined
Dec 29, 2014
Messages
51
Location
Gatineau, Québec
First Name
René
Willys Model
  1. Pickup
Willys Year:
  1. 1956
I have an issue where the brake pedal does not return when i brake.
i do have a return spring.
I think i will take the master out ans clean it, but i am afraid that the 4 wheels will have to come off and the cylinders will need replacement also.
Did anyone else have this issue and how was it resolved? and i going at it the right way?
 
How sift is the pedal ? Have you greased it? I would disconnect the rod between the pedal and MC and see if the pedal returns on it's own for starter.


Nick
 
Several possible issues here, and the experts will chime in. Is the spring still good? Just because it's there and intact doesn't mean it's still holding strong tension. Is the pedal binding on the cross rod? Worn bushings, worn rod, or possibly debris/lack of lubrication may be magnifying the issue. If it's just the pedal and not the brakes themselves (are they hanging up when you release the pedal?) it should be easy to diagnose, but not nessecarily an easy fix. Brake shoe return springs would cause brake shoe issues, but I don't think that would affect the pedal itself. A good visual inspection underneath should provide some answers.
 
Great idea. i tried greasing it, but even when i changed the grease nipple, can't push any grease. will try removing the rod first, thank you.
 
The pedal should return no matter what's going on in other parts of the braking system. Rob is correct to start your diagnosis around the pedal itself -- the return spring and pivot bushing. Also just be sure the pedal has free motion and isn't rubbing against something.
 
Thank you everyone, i did remove the rod and still the pedal will not come back on it's own, i have to pull hard, so it appears that the bushing/post/spring are a large part of the problem. I guess i will have to break it apart, clean everything and order new bushing and springs. I also saw some real nasty brown juice where the rod came out... so I guess a new master cylinder would not be a bad idea. What are your thoughts of the dual that Overland-Willys sells?
here are a few pictures of my setup
attachment.php
attachment.php
attachment.php
attachment.php
 

Attachments

  • IMG_20160627_203047.jpg
    IMG_20160627_203047.jpg
    83.6 KB · Views: 38
  • IMG_20160627_203059.jpg
    IMG_20160627_203059.jpg
    60.4 KB · Views: 38
  • IMG_20160627_203117.jpg
    IMG_20160627_203117.jpg
    45.8 KB · Views: 38
  • IMG_20160627_203205.jpg
    IMG_20160627_203205.jpg
    55.9 KB · Views: 38
Yep, if it's leaking now is a good time to replace it for sure. One of the members on here sells a dual master cylinder kit that is correct for these wagons/pickups. Many of the kits the other vendors sell will end up with a soft brake pedal. You'll be looking at the $300-400 range for one of those kits. They are much safer than the original setup however.

If you go with a factory master cylinder, you can buy them on RockAuto.com for about $30-40. They are cheap enough that it's really not worth the time to rebuild them. I would go ahead and replace the T-fitting coming out of the end and the pressure sensor at the same time. The T-fitting and brake light sensor can both be purchased from Walcks or any other vendor.
 
Thanks Silicond17, whos sells the dual master cylinder kit? will also look at the T fitting and pressure sensor. If my rod is pitted, can i just glassbead it and make it all nice? if i put Por15 on it will it hold with the brake fluid?
 
Here's his thread, his contact info is in there:
http://www.oldwillysforum.com/forum...cylinder/page8&highlight=dual+master+cylinder

Sounds like a very knowledgeable guy. I would definitely go with his kit over the other vendors because it's designed specifically for our vehicles rather than just thrown together.

I would go ahead and replace the T-fitting, the bolt (banjo bolt?), and the copper crush washers (2). If the rod is pitted you're probably fine just cleaning it up. If you're ordering the dual master cylinder kit, it will come with everything you need.

POR-15 doesn't hold up to brake fluid. I rebuild my master cylinder about 6 years ago and painted it with POR-15 silver. It never leaked, but just from spilling some brake fluid on it while filling it, it did not hold up well at all. I used cheap Rustoleum on my CJ master cylinder when I replaced it a couple years ago, and believe it or not, it has held up better than the POR-15. For numerous other disappointing reasons, I have entirely stopped using POR-15.
 
Back
Top